Forums
https://www.decware.com/cgi-bin/yabb22/YaBB.pl SUPPORT FORUMS FOR DECWARE SPEAKER PLANS >> Housewrecker Support Forum >> quad loading https://www.decware.com/cgi-bin/yabb22/YaBB.pl?num=1186777776 Message started by iowadave on 08/10/07 at 21:29:29 |
Title: quad loading Post by iowadave on 08/10/07 at 21:29:29 I am building a home wrecker and reading through people's experiences. Had a questions about changing out subs after the box is completed. for example, if I quad load the box now and feel that i dont need (4) 15"s (who really does, but if your here...) how can i go about removing the two subs in the middle of the box. the top and bottom ones will come out no problem, but the inner two will not fit through the baffle. Should I just seal the top and bottom lids and keep the side removable? or if i build the box with the 4 subs will they be stuck in there for the life of the box? |
Title: Re: quad loading Post by 60_and_up on 08/10/07 at 23:49:15 you join 2 subs together with a baffle between them and mount the 'clamshelled' pair from either end. |
Title: Re: quad loading Post by speakerfreak7 on 08/11/07 at 01:20:39 i made mine with the removable side panel. it works fine and i can get to anything i need to easily. |
Title: Re: quad loading Post by HT-EXT on 08/13/07 at 11:26:03 I have the top and bottom lids removeable and clamshelled the two woofers directly together for each end. You can then insert them as a pair into the top and bottom. After testing the combo you can easily remove one woofer from each end and leave the other two. Of course you will have the magnets in the middle chamber if you leave the alignment as is but it will not be too hard to turn one around if desired. I prefer just two woofers vs. quad-loading. Quad-loading takes alot of power but is very good for reproducing the lower frequency ranges. It is really up to personal taste if quad-loading is your favorite or will two do enough damage. I have tried both set ups and was satisfied with just two. It is more than enough to piss-off the neighbors. HT-EXT |
Title: Re: quad loading Post by iowadave on 08/14/07 at 20:28:32 Thanks. I see my problem now. I was thinking that the baffle was required to go between the woofers(like the first pic). oh well, next time. Did find some spare time this weekend and finished the box. Packed in two 15"ers pointed up. Sounds great! Hits low! low res pics, but you get the idea ![]() ![]() ![]() |
Title: Re: quad loading Post by iowadave on 08/14/07 at 20:34:25 That is a DB12 sitting next to it for a size comparison |
Title: Re: quad loading Post by Bart_West-VL. on 08/14/07 at 22:17:18 Cool! especially with the comparison next to the DB12". I'm not sure, did you put in two pair of drivers or two single drivers? What drivers are there in the box? Did you place the bottom ports firing towards the wall? Thanks for the pictures! Bart. |
Title: Re: quad loading Post by iowadave on 08/15/07 at 16:29:17 (2) Rockford Fosgate Punch 15" one 15" mounted to each baffle pointed up powered with about 50watts to each woofer from a sony receiver i bought in '98. went old school and used a coffee can and rounded over the lower ports with some sand paper. Thought about using the router... I have not found the final location for where the box will be kept. still moving it around and facing the ports in every direction. more than likely it will stay where it is, @45degree w/ ports facing a corner. I have a DB8 and 15" wedge too, i will snap a pic of them all together one of these days. who doesnt like pictures? |
Title: Re: quad loading Post by Bart_West-VL. on 08/15/07 at 18:45:43 I think you might want to reconsider the rounding of those lower ports. They need to stay straight, these are tuned to a certain frequency and effectively have a length of 3/4" to get to that tuning. Rounding them will tune the lower part of this box higher. |
Title: Re: quad loading Post by shayneyasinski on 08/16/07 at 05:53:02 o and a party rocks wow is that hw sounding good?? shayne |
Title: Re: quad loading Post by iowadave on 08/16/07 at 17:26:40 Glad i didnt go over the ports with the router :o I just smoothed over the edges. Definitely will leave them alone from here on out. chocolate rain...this box is like crack for my brain! O&A Dig this box a lot! The top port seems to allow me to put the box anywhere and still get good output. the DB12 was touchy with it's single port. |
Title: Re: quad loading Post by HT-EXT on 08/16/07 at 19:51:18 You can router the lower ports without much change in tuning. By doing this you can cut down on turbulance and maybe even port fart if you have such a problem. I have router both sides of the my HWK15 lower ports and tuning stayed the same. This is an option, you can just smooth the outsides of the ports like you said and have the same results. As far as clamshelling the only issue would be if the outside surround is to big and comes into contact with the other woofer's surround. A spacer or weather striping could be used to separate the woofers just enough to keep the surrounds from touching. If you need more info let me know. HT-EXT PS: GREAT JOB ON THE BUILD!!!! |
Title: Re: quad loading Post by Gexter on 08/17/07 at 01:29:58 You beat me to the post HT-EXT there is always a fudge factor or error correction. WIN-ISD has a correction for example. Rounding them off and smoothing the edges will help with noise. the freq diff is minimal. Ditto on the job. I also like the comparisons Gex |
Title: Re: quad loading Post by HT-EXT on 08/17/07 at 11:39:36 Sorry GEX. I haft to do something to get my post up. All I want for christmas is to be a SENIOR MEMBER! HT-EXT PS: For all you funny people out there I don't think VIAGRA will help get my post up in this situation. Tee Hee |
Title: Re: quad loading Post by Gexter on 08/18/07 at 00:18:48 LOL on the first. Groan on the second. Gex |
Forums » Powered by YaBB 2.2.2! YaBB © 2000-2008. All Rights Reserved. |