Forums - Pre amp or monoblocks

09/09/26 at 17:10:21

Most recent 50 posts
Welcome, Guest. Please Login or Register

Forums » General Discussion and Support

‹ Previous topic | Next topic ›

Pages: 1

Pre amp or monoblocks (Read 7277 times)

Sysygy Ex Member	Pre amp or monoblocks 05/23/09 at 15:18:18 I have a Zen Select that has matched amazingly well with some JM Reynaud Trentes. I think they are 89 db. They play very comfortably in my bedroom but a little more volume would be nice. I have never had a preamp before, so I don't know if it will allow more headroom or not vs the second amp which I figure definitely will. Thanks
Back to top	IP Logged Share: Likes:

Doorman Seasoned Member Offline "pouring from the empty into the void" Posts: 451 x1\|Royston\|Canada\|Canada\|48\|35	Re: Pre amp or monoblocks Reply #1 - 05/23/09 at 15:24:58 My Select is a very different beast with a (tubed) pre in the chain. Dynamics particularly are much improved IMHO. The ability to easily switch between sources is an added bonus. Adding another Select would be the ticket! Don
Back to top	Decware, Rega, Heybrook/Linn/Ortofon Goertz/Wireworld/cat-5/MarkAudio Alpair 10.2 drivers (eN) in DIY Mar-Ken cabs NHT SB3’s IP Logged Share: Likes:

Sysygy Ex Member	Re: Pre amp or monoblocks Reply #2 - 05/23/09 at 15:33:44 Dynamics. I should have been more clear. I am not really looking to achieve a greater listening level, I would prefer not to clip during a big dynamic swing. Thanks for the input.
Back to top	IP Logged Share: Likes:

sebrof

Ex Member

Re: Pre amp or monoblocks
Reply #3 - 06/17/09 at 15:52:00

I have a similar question to what Sysygy brings up.
I built a Zkit1 and it sounds great with my 104db Klipschorns, I'm very pleased. Many many things to think about tweaking in the coming months.
I am considering either adding a decware preamp kit and bypassing the Zkit1's pot, or adding a 2nd Zkit1 and bridging (using 1 pot for 2 amps).

What would the effect be of adding a Decware preamp kit to the Zkit1?
What would be the effect of biamping 2 Zkit1s besides more headroom?

Thanks,
Mike

IP Logged

Likes:

dank

Seasoned Member

Offline

pair of dual 18
Imperials

Posts: 425
x1|Ramsey|USA|USA|308|86|MN,Minnesota

Re: Pre amp or monoblocks
Reply #4 - 06/17/09 at 22:53:47

Sysygy

You could try a one channel test with just the Zkit1 you have. Try bridging the amp (either series or parallel) to drive one speaker, then compare that to the Zkit1 driving a single speaker unbridged. Maybe that will tell you what you will gain by adding a 2nd amp.

Also, be sure to check pin 6 on your output tubes. If its open and you are using 6p15p-ev tubes you are not getting full power out of your Zkit1. See "Zkit1 (SE84DIY) problems" thread under Zkit 1 support forum and "Christmas Comes Early" thread under General Discussion /support forum

Dan

IP Logged

Likes:

Lon Seasoned Member Online "Love without guts is worthless!" Philip K. Dick Posts: 28760 Munson Township, OH	Re: Pre amp or monoblocks Reply #5 - 06/17/09 at 23:53:02 From my experience, if you just want dynamics added the CSP2 will do that, and add "weight." But if you want lots of headroom and more speaker options, add another Select.
Back to top	HR-1,ZBIT,ZROCK3,SEWE300B,Dynagrid Jr;Rega RP3+all GrooveTracer mods;PSAudio:PST+DSD DAC Mk II,NPC,PowerBases,AC-12 pwr cbls, Reference spkrcbls,GCHA;Mapleshade SamsonV3;VeraFi Audio cpts VooDoo:Stradivarius interconnects;Stack EQ; phones:Sennheiser HD800S,ZMF Ori IP Logged Share: Likes:

shuijing Ex Member	Re: Pre amp or monoblocks Reply #6 - 06/18/09 at 04:58:05 Good!
Back to top	IP Logged Share: Likes:

Sysygy Ex Member	Re: Pre amp or monoblocks Reply #7 - 06/24/09 at 03:25:41 Dank, I have a Select, but it is a good idea for an experiment. Lon, simple good advice. I have had the amp for a little while now and it plays loud enough. If I spend more money it will be for the pre. I have to buy "the Cube" for my Hornshoppe Horns first though.
Back to top	IP Logged Share: Likes:

Pages: 1

‹ Previous topic | Next topic ›