Welcome, Guest. Please
Login
or
Register
08/14/24 at 21:00:43
Most recent 50 posts
Forums
›
AUDIO FORUMS
›
D.I.Y.
‹
Previous topic
|
Next topic
›
Pages: 1
DIY Open Baffle Tool recommendations (Read 1668 times)
kulafu
Seasoned Member
Posts: 233
DIY Open Baffle Tool recommendations
06/25/22 at 13:34:11
Greetings DIY experts! I am considering building my own DIY Open Baffles. By me asking this implies that I am a 'Beginner' so please be kind.....
. As a minimum, I think I understand I would need a router and a circle jig to cut the hole. Any advice from the respectable DIYers would be greatly appreciated. I have done some research on how to cut large diameter holes but I have not found DIY videos on how to build O/Bs. I have a looked at several circle jigs so brand and type recommendations would be appreciated! Thank you!
Bob
Back to top
Altec 604 8K, Liionidas Silver 10/W-15,UFO25th/Cary SET Monos/Torii Jr,CSP3 25th/Holo May KTE ,HQP/USB/Pulse/EtherRegen, Roon/Thorens 1600(Decware ICs, speaker wires/Equi=Core 1800, SFDBs and future STR-1002)
IP Logged
Donnie
Seasoned Member
Why does it hurt
when I pee?
Posts: 2246
Re: DIY Open Baffle Tool recommendations
Reply #1 -
06/25/22 at 14:08:36
I use this hole jig.
https://www.lowes.com/pd/Milescraft-CircleGuideKit/1000233663
It is a little clunky but does the job.
I use this router, a little overkill for most usage, but is very nice.
https://www.lowes.com/pd/Bosch-12-2-25-HP-Variable-Speed-Combo-Fixed-Plunge-Cord...
I built my first open babbles with a jig saw and a hand drill. Yes I drilled hundreds of 3/16' holes side by side to cut out my driver holes.
My motivation was much higher back then.
Back to top
Owner of the infamous RED TORII and Dan the Redheaded Amp
IP Logged
Sean
Seasoned Member
Posts: 332
Re: DIY Open Baffle Tool recommendations
Reply #2 -
06/25/22 at 17:11:03
I have the same router as Donnie. I also have the Bosch trim router that is smaller and easier to handle. Both have circle cutting attachments sold separately. You can also diy a circle cutting jig for it fairly easily. Two rods, a chunk of scrap wood and a few screws. There are multiple YouTube videos on how to make one. The basic idea is drill a hole for the router bit at he inside edge of the hole. Mount the jig at the center point of the hole. Firmly grasp router and rotate it on center pin to cut the hole.
Jig saw works too. Slow and steady. Sneak up on your line. Expect to have some sanding to get things nice and round.
But wait…you can also use a hole saw for a drill or a forstner bit to drill out the edge of the circle. This will make a rough hole that requires even more sanding.
Back to top
Technics 1210G, Phasemation PP-500, Cinemag 1254 SUT, ZP3, CSP2+, UFO25, Tekton Pendragon
Schiit Bifrost, Mac Mini, Roon
IP Logged
kulafu
Seasoned Member
Posts: 233
Re: DIY Open Baffle Tool recommendations
Reply #3 -
06/25/22 at 20:23:58
Donnie and Sean, thanks!
Bob
Back to top
Altec 604 8K, Liionidas Silver 10/W-15,UFO25th/Cary SET Monos/Torii Jr,CSP3 25th/Holo May KTE ,HQP/USB/Pulse/EtherRegen, Roon/Thorens 1600(Decware ICs, speaker wires/Equi=Core 1800, SFDBs and future STR-1002)
IP Logged
Sam S
Verified Member
Posts: 18
Re: DIY Open Baffle Tool recommendations
Reply #4 -
06/25/22 at 23:57:16
Hi Bob,
I am in the same boat - a total novice.
I got a plunge router from Harbor Freight for like $75
Haven't tried it yet, but for me it only has to work a few times :P
Here are a couple of good videos on making your own jig:
https://www.youtube.com/watch?v=4YPqfHInnyo
And for them really huge drivers:
https://www.youtube.com/watch?v=X1cRm6sF-nI&t=7s
Sam
Back to top
IP Logged
Pages: 1
Forums
›
AUDIO FORUMS
›
D.I.Y.
‹
Previous topic
|
Next topic
›
Forums
» Powered by
YaBB 2.2.2
!
YaBB
© 2000-2008. All Rights Reserved.