Forums - Another speaker project

EdwardT Seasoned Member Posts: 366	Another speaker project 07/19/23 at 23:51:41 Apparently I did not know that our current tower speakers are too big but I have been so informed. Cool, I needed a fun project and Padauk it is.
Back to top	IP Logged

Donnie Seasoned Member Why does it hurt when I pee? Posts: 2477	Re: Another speaker project Reply #1 - 07/20/23 at 10:04:36 Those speakers look familiar. What are they?
Back to top	Owner of the infamous RED TORII and Dan the Redheaded Amp IP Logged

EdwardT

Seasoned Member

Posts: 366

Re: Another speaker project
Reply #2 - 07/20/23 at 17:50:00

They’re GR X-LS flat packs. The current plan is to migrate the components from the existing 39” tall X-SLS to these 13.5” cabs. Same electronics and speakers for both and my speakers are broken in. I’m daydreaming up a stand that'll raise/lower with minimal effort so I don’t kill the listening experience totally. Anyway, it’s too hot to get farther along than this.

Back to top

IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #3 - 07/21/23 at 20:53:00 Bottom and back ready for trimming by file.
Back to top	IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #4 - 07/23/23 at 22:24:38 A Burns moment: “The best laid schemes o' mice an' men / Gang aft a-gley.” I ironed a wrinkle into the radius, and no amount of fettling would remove it. So, apply heat, remove beautiful veneer, and, hand plane the glue off the sides and the front. Sand, clean, reapply glue and new veneer.
Back to top	IP Logged

Donnie Seasoned Member Why does it hurt when I pee? Posts: 2477	Re: Another speaker project Reply #5 - 07/24/23 at 17:14:19 "It isn't how good your work is, it is how good you can hide your mistakes"
Back to top	Owner of the infamous RED TORII and Dan the Redheaded Amp IP Logged

Same Old DD

Seasoned Member

Posts: 1070

Re: Another speaker project
Reply #6 - 07/24/23 at 21:02:03

Extra icing or more mayo or a pickle garnish is not available to woodworkers.

I've only done veneer a few times and I swore off after the first time. I kept trying. It is much more involved than it looks.

Are you using plain wood and wood glue, pre-glued veneer or contact cement? Curious.

Only results matter!
You're doing a great job.

Back to top

SE84Cs Mono'ed, Lii Audio F15 OB, W15 "H" Frame Subwoofer, McIntosh MC2500, Lazarus Pre, Dual TT, Ortofon, Kleenline Iso Power, Revox, Crown R-R, Pioneer Elite Digital Source

IP Logged

4krow

Seasoned Member

IMAGINE WHIRLLED
PEAS

Posts: 1679

Re: Another speaker project
Reply #7 - 07/24/23 at 21:36:31

It was such a relief to me when I handed my unused supply of veneer to a former friend. Ok, no we are still friends, but your riding the edge when you offer up such a gift.
I visited Kurt yesterday, and he was quick to show me the antique sewing machine that his mother used. Back in those days, it was veneered in oak. Now it appears to be a change in thought, and it is a BLACK PAINTED TOP. Milk paint of course, veneer is in pieces from the first and final try. God bless you Kurt. I would have done the same.

Back to top

Decware 34I.3 integrated amp/Forte' 3 bass amp/Velodyne SMS-1 bass mngmnt system/Decware ZOB speakers/Audio Nirvana 8" bass drivers/Xiang Seng DAC/ LR Audio Computer/Rega Apollo R CDP/Emotiva ERC3 CDP/BPT 3.0 power cond.

IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #8 - 07/25/23 at 13:21:37 DD: I’m using Heat Lock glue and an iron. The glue dries hard before you bond it which allows easy alignment and as long as I don’t rush the process it’s not too difficult. Also easy to make an unrecoverable error, so there’s that.
Back to top	IP Logged

Same Old DD Seasoned Member Posts: 1070	Re: Another speaker project Reply #9 - 07/25/23 at 14:10:14 Very cool! The enclosures look great! Kind of nice having the works to slip right in after the wood is finished.
Back to top	SE84Cs Mono'ed, Lii Audio F15 OB, W15 "H" Frame Subwoofer, McIntosh MC2500, Lazarus Pre, Dual TT, Ortofon, Kleenline Iso Power, Revox, Crown R-R, Pioneer Elite Digital Source IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #10 - 07/25/23 at 21:47:41 All of the routing is done, it’s up to the razors and files now to clean everything up. I'm applying water to all of the bearing edges where you can see the tool left a mark to swell those fibers before sanding.
Back to top	IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #11 - 08/03/23 at 18:26:03 I think I’m done trimming the edges and the tweeter inlet rings just need another touch up but they’re closing in on the finish.
Back to top	IP Logged

Donnie Seasoned Member Why does it hurt when I pee? Posts: 2477	Re: Another speaker project Reply #12 - 08/04/23 at 01:04:07 Looking good!!
Back to top	Owner of the infamous RED TORII and Dan the Redheaded Amp IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #13 - 09/26/23 at 17:29:02 A nice blister appeared after sitting in an overheated shop and it’s slowed progress I had an idea… I need to touch up that spot but it seems to have worked.
Back to top	IP Logged

EdwardT Seasoned Member Posts: 366	Re: Another speaker project Reply #14 - 10/14/23 at 13:57:02 I need a better stand idea. This accomplishes a complete system turnaround; understanding my hearing loss helped me change to a system that can help compensate for the massive frequency loss and make listening enjoyable again.
Back to top	IP Logged

Donnie Seasoned Member Why does it hurt when I pee? Posts: 2477	Re: Another speaker project Reply #15 - 10/14/23 at 15:59:28 Edward, Very nice job! They look professionally done. I am also trying to come up with an original idea for a interesting stand. My mind hasn't been very fertile with any ideas yet. How are those Tube Connectors? I have always wondered how they compare to regular binding posts? Anyway, great job!
Back to top	Owner of the infamous RED TORII and Dan the Redheaded Amp IP Logged

Lon Seasoned Member "Love without guts is worthless!" Philip K. Dick Posts: 27840	Re: Another speaker project Reply #16 - 10/14/23 at 16:06:27 Awesome! Excellent work.
Back to top	HR-1,ZBIT,ZROCK3,SEWE300B,Dynagrid Jr;Rega RP3+all GrooveTracer mods;PSAudio:PST+DSD DAC Mk II,NPC,PowerBases,AC-12 pwr cbls, Reference spkrcbls;Mapleshade SamsonV3;VeraFi Audio cpts VooDoo:Cremona+Amati interconnects;Stack EQ; headphones:Sennheiser HD800S,ZMF Ori IP Logged

EdwardT

Seasoned Member

Posts: 366

Re: Another speaker project
Reply #17 - 10/14/23 at 18:37:29

Thank you.

The tube connectors make for a nice clean entrance but I don’t use the male end because it feels like banana plugs fit tighter (and any sonic improvement is likely negated) and for me, tight is better.

Replicating/modifying this Stickley fern stand is my purloined idea for stands, along with a set of Fat Dots that are in use now.

Back to top

IP Logged

Tony Seasoned Member "Life without...music is inconceivable" A.Einsteln Posts: 852	Re: Another speaker project Reply #18 - 10/15/23 at 05:44:51 Edward, What a nice job you did on that stand. 👏 It's beautiful.
Back to top	SE84UFO25 \| CSP 2+ \| STR-1002 \| Ic0n4 \| Lumin U2 Mini w Elite BDC MK II\| Carver C-9 \| Denafrips Terminator DAC \| Denafrips Gaia DDC \| Vera-Fi LNBH, SSZ, SDFB & AC Tuning X \| Decware I/Cs \| Decware Pwr Cbls \| ZWIRE Speaker Cbls \| Omega SAHOM & KEF KC62 IP Logged

4krow Seasoned Member IMAGINE WHIRLLED PEAS Posts: 1679	Re: Another speaker project Reply #19 - 10/15/23 at 07:11:10 It is always good to see this level of woodworking. Not many people are really capable of it these days.
Back to top	Decware 34I.3 integrated amp/Forte' 3 bass amp/Velodyne SMS-1 bass mngmnt system/Decware ZOB speakers/Audio Nirvana 8" bass drivers/Xiang Seng DAC/ LR Audio Computer/Rega Apollo R CDP/Emotiva ERC3 CDP/BPT 3.0 power cond. IP Logged